. Contents Introduction. 1 Display Standing Blanking.2 IMPORTANT Consumer INFORMATION. Intro Like to the eurosec control cell. Your installation organization will have programmed your program to shield your property to the highest feasible standards. Several user programmable choices are available that will end up being covered afterwards in this manuaI.

• Oceanic Veo 1.0 User Manual

Where I can get eurosec pr5208 rev 1.0 user manual - Cars & Trucks question. The Eurosec security system can be purchased from and installed by any security company. Eurosec CP8 User Manual. 'Instructions for a Eurosec Alarm.'

Throughout this manuaI, reference will end up being made to the Expert User Code, the stock place default will be 5678. Display Standing Blanking Based on Handle Panel set up, it may end up being a requirement that the Status (Established or Unset screen) of the security system will be not shown. Arranged or Unset Standing will just be displayed for ten seconds when the system is Set or Unset. The bottom series of the screen will then be blanked off.

Total Establishing the System. Two methods are obtainable for Full Place. After checking out the premises are protected: Enter a legitimate User Code followed. If allowed by the installation engineer. The departure firmness will right now sound. Departure the premises via an sanctioned exit path. Pre Departure Check out.

At the begin of the setting treatment, a problem Exit Right now!. Firmness will noise if any non leave routes are Area 3 open up. The screen will show, for example:- If the problem clears within 20 mere seconds after that the exit overall tone will begin, if not, the fault overall tone will carry on until a legitimate User code is entered. Part Placing the Program (making use of Component 2 or 3). Two other Part Sets may become obtainable for your program. Component 2 can be a 2nd place of areas that may be omitted and Component 3 will combine Component 1 and Component 2.

Oceanic Veo 1.0 User Manual

To use Component 2 or 3. Enter a valid User Code adopted by 2 or 3.

Unsetting the System. Enter the premises via an sanctioned Entry Stage. The entry color will noise. Proceed to the key pad and get into a valid User Code. Display After an Security alarm.

If an alarm takes place when the system is arranged, the trigger of the security alarm will become displayed for 10 secs after you unset the system. Resetting After an Alarm After an security alarm the program desires to end up being reset.

Your installation corporation will possess designed the reset to zero settings for your system so that it conforms with your insurance plan business and legislation needs. Your set up corporation will have got educated you as to the kind of reset that your system is fixed for.

If a Get better at Code Reset to zero has long been designed by the professional, a higher degree of program code will be required. If Alarm Reset offers been programmed for Get better at, after that the display will display, for example, each time the Consumer tries to fixed!!!. If Anti has been designed for Security alarm Reset, contact the Main Train station or Professional, (as advised by the Set up Firm) and estimate the quantity provided by the screen. The main place or engineer will give a return Anti-Code (this may contain the (Affirmative). Tamper Resetting With the screen telling:-!!!! Enter a valid User code.

The program is today reset. Setting up the program with Mains FaiI In the occasion of a brief term energy trim, where it is definitely known when strength will become restored, (at the.gary the gadget guy. Enter your Consumer Code once again adopted. If enabled by the set up professional.

The get out of shade will right now sound. Leave the property via an sanctioned exit route. Take note: Pushing the (Quick) essential during get out of will cut short the get out of time to 3 seconds. Re-setting the screen after a Máins Fail If thé system has been programmed for Any code reset; With the display showing:-!!!! Enter your Consumer code Then press Reset to zero. The screen is today reset.

Programming User Codes Up to nine user codes may be programmed on predetermined levels. Consumer Numbers 1 to 3 Get better at Level. Allows Place, Part Collection, Unset and Consumer Programming Setting. User Quantities 4 to 7 User Level. Allows Collection, Part Place and Unset.

User Numbers 8 to 9 Set Only Degree. Press (Zero). Do You Need to. The display will show:- Program Rules? 9 The display will show:- Push a solitary digit corresponding tó the user amount (1 to 9) that you wish to plan. The display will display for example:- Program code # # # #.

Text is inserted in a identical method that you would get into text on a mobile phone. Select heroes from the listing below:- YZ blank Enter the needed character followed by (Yes). Continue until you have came into eight character types.

Perform You Would like to. The display will show:- System Rules?. Programmable User Options Many user programmable choices are obtainable via user rules 1, 2 or 3. To make use of these choices please follow instructions beneath. Delete Area Choice This choice allows personal specific zones to be deleted (disregarded) when the system is being set. Notice: Area delete can be only effective for one Place and will require to end up being repeated for following Sets. Press 0 double.

Do You Wish to. The screen will show for example:- Established User 1? Press (Total) for Full Set Push (Part) for Component 1 Set Press 2 for Part 2 Set Press 3 for Component 3 Set The system will right now begin the relevant Place, with the specific zones you erased eliminated from the Place. Walk around the area being tested. As each device is managed there will a overall tone from the internal sounders and the display will show the triggered outlet. To test the bells (external sounders) and strobe press 9. To stop the bell test press 9 once again.

To escape back to Unset press 0 three moments. Setting Period Date Enter a valid Master Consumer Code followed by (No). Perform You Want to. The screen will show:- Test? Do You Want to. The display will show:- Delete Area?

Do You Need to. Enter the period making use of the 24 Hour clock at the.g 2300 for 11pm adopted by (Okay).

The screen will show, 03 Jul 23: 00 for example:- Okay? Press Yes ! to accept. Perform You Need to.

The display will show:- Established Time / Period? To return to the Unset Setting press 0 twice. Reading through the Log Enter a legitimate Master Consumer Code implemented by (No).

Do You Want to. The display will show:- Check? Perform You Want to. The screen will show:- Delete Area? Do You Wish to. The screen will show:- Select Choices?. To come back to the Unset Setting press 0 three moments.

Note: Durante control -panel only.The the journal may store up to 256 occasions with time and date stamp. Non EN control board. Depending on the Record mode Take note: designed by your set up engineer the record may store 256 events with no period or date stamp.

System Details Installation By: Deal with: Tel: Fax: Zone No. Area Kind Chime Installation Date Support Timer Serviced Next Thanks Serviced Next Thanks Notes. Installed By:- RISCO Team UK Ltd reserve the best to change the software program and features without earlier see 5INEULCDUM ver C PR5202 Rev1.4.